Outdoor Bar Stool - Metric

 Write Review

buildsomething added on 7/26/2017

This handsome stool makes a perfect companion to any outdoor bar height table, but it would also be great in lots of other places. At just about 610mm tall, the stool is just right for a standard-height counter or island. You can build one from just four boards—we chose cedar boards for outdoor us


Follow the steps below to complete this project.


Gather Your Materials

Before you go get your lumber and supplies, decide how many stools you want to make. The materials list and cutting diagram show what you’ll need to build one stool. So, if you’re building two stools, you’ll need twice as many boards. Each stool also requires about 60 pocket-hole screws, so we specified one 100-count box. You’ll need to get more screws, as well, if you’re building more stools. Speaking of the screws, we used Kreg® Blue-Kote™ screws, which are designed to resist moisture for outdoor use. Also be sure to choose waterproof, or at least water-resistant glue. Standard wood glue won’t withstand moisture outdoors.

 How To Choose the Correct Kreg Screw

Learn how to choose the correct Kreg Screw for your project based on the material you are using and where you'll place the project—indoors or outdoors.


Cut the Legs

Set your miter saw to 5°, and then cut four Legs to length from a 19mm x 64mm board, as shown in the cut diagram. Note that the leg measurement is shown from long end to long end. Also, for the legs, the angles on the ends should be parallel. By the way, if you’d like to make taller stools, you could make the legs longer.

 How To Cut Angles on a Miter Saw

Learn how to make two kinds of angled cuts on a miter saw: A miter cut and a bevel cut. A miter saw makes them easy, and allows you to expand your project-building capabilities.


Make the Side Rails

Cut two Long Side Rails and two Short Side Rails to length from a 19mm x 64mm board, as shown in the cut diagram. Note that this time, the angles on the ends aren’t parallel. They’re opposed to create a “wedge” shape. When cutting, you’ll need to cut one end, and then swing your miter saw 5° in the other direction before cutting the other end. Or you can flip the board over—so the opposite edge is against the fence for the second cut. Once you have the pieces cut, set your pocket-hole jig for 19mm thick material, and then drill pocket holes in each of the Rails, as shown. Cedar typically has one smooth face and one rougher face. For the best look for this project, drill the pocket holes in the rough face of the rails—and in the rest of

 How To Set Up a Kreg Jig in Three Simple Steps

Learn how easy it is to set up a Kreg Jig® and ensure that you'll drill pocket holes accurately every time.


Assemble the Sides

Set the one Long Side Rail against one first Leg at the location shown, making sure that the Leg is oriented correctly. Assemble the parts using waterproof exterior wood glue and 32mm Blue-Kote™ Kreg Screws. Next, set the Short Side Rail flush with the upper end of the Leg, as shown, and secure it with glue and screws. Next, add the second Leg to complete one stool side. Repeat this to create the stool side. Sand the outside face of each side as needed, and sand the inside face enough to remove just the loose wood fibers.

 How To Use a Drill Clutch

Learn how to use a drill clutch to control the drill's power and performance, so that you'll always get great results when drilling holes and driving screws.


Make the Foot Rails and Caps

Cut two Foot Caps and two Foot Rails to length from a 19mm x 64mm board, as shown in the cut diagram. Drill pocket holes at the locations shown. On each Foot Cap, ease one long top edge, as shown. If you have a router, you can do this with chamfer bit. If you don’t have a router, you can sand the cedar quickly to shape.


Make the Seat Rails

Cut two Seat Rails to length from a 19mm x 64mm board, as shown in the cutting diagram. Drill pocket holes at the locations shown. Sand the pieces as needed—but don’t sand the ends.


Attach the Foot Cap and Rails

Lay one of the side assemblies on a work surface with the pocket holes facing up. First, set a Foot Cap in position so the upper face is flush with the upper edge of the Long Side Rail, as shown. The eased edge should point outward. Attach the Foot Cap to the Leg using glue and 32mm Blue-Kote™ Kreg Screws. Next, position the Foot Rail so it is centered under the Foot Cap, and then glue and screw it to the Leg and the Foot Cap. Repeat this to attach the other Foot Cap and Rail. Then position the Seat Rails as shown and secure them to the Legs with glue and screws.


Add the Second Side

Attach the other Side frame assembly to the Rails and Cap the same way as the previous step to complete the base.


Make the Seat Slats

Cut three Seat Slats to length from a 19mm x 140mm board, as shown in the cut diagram. Drill pocket holes at the locations shown in just two of the three Slats.


Assemble the Seat

Glue and clamp the three Seat Slats together shown. Secure the three boards together using 32mm Blue-Kote™ Kreg Screws. Sand the seat flat as needed.

 How To Select the Right Sandpaper

Learn how to choose sandpaper that will give you great results on wood projects—without having to sand too much. 


Install the Seat

Lay the seat assembly on a flat work surface with the pocket holes facing up. Flip the stool base assembly upside down and place it on the seat so that it’s centered, as shown. Then secure the frame to the seat using glue and 32mm Blue-Kote™ Kreg Screws.


Apply the Final Finish

Complete any final sanding, clean the stool, and then apply a quality exterior finish. We used “Cedar Natural tone” stain (transparent).

Tools Used:

Materials Required:

Wood Products:

(1) 19mm x 64mm, 2400mm, Board  
(2) 19mm x 64mm, 1800mm, Board  
(1) 19mm x 140mm, 1800mm, Board  


(1) 100 count box 32mm Blue-Kote™ Kreg Screws Shop Online
(1) waterproof wood glue Shop Online

Parts/Cut List:

(4) Leg, 19mm x 64mm x 603mm cedar  
(2) Long Side Rail, 19mm x 64mm x 330mm cedar  
(2) Short Side Rail, 19mm x 64mm x 257mm cedar  
(2) Foot Rail, 19mm x 64mm x 330mm cedar  
(2) Seat Rail, 19mm x 64mm x 330mm cedar  
(2) Foot Cap, 19mm x 64mm x 330mm cedar  
(3) Seat Slat, 19mm x 140mm x 419mm cedar  


No extra details have been uploaded.  


You must log in to add comments


    Become a Member


    • Connect with the BuildSomething Community
    • See what others build and share your stories


    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed


    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com



    Already a member?
    Sign in!

    Kreg Tool