Moore Family Farmhouse Table

 Write Review

jenwoodhouse added on 4/8/2017

This beautiful farmhouse dining table will seat 8 people comfortably. Store-bought turned furniture legs and off-the-shelf lumber make this table an easy and accessible DIY project.

Directions

Follow the steps below to complete this project.

1

Build the Carcass

Measure, mark, and cut the 2x4 aprons to length. Drill 1 1/2" pocket holes into the ends of the aprons, position them 3/4" inset from the outside edges of the legs and attach with 2 1/2" pocket screws and wood glue. Check for square and adjust if necessary.

2

Add Tabletop Supports

Measure, mark, and cut the 2x4 supports to length. Drill 1 1/2" pocket holes into the ends and attach, as shown, to the long aprons with 2 1/2" pocket screws and wood glue.

3

Build the Tabletop

Using a table saw, rip 1/8" off of each edge of the 2x8 and 2x10 boards. This will square up the bullnose edges of the boards and ensure a tighter joint. The 2x10 boards should now be 9" wide and the 2x8 boards should be 7" wide. Measure, mark, and cut tabletop boards to length. Edge-join the boards together with wood glue. Be sure to spread the glue evenly over the entire surface of the edges. Use clamps and cauls to ensure the boards are tight, aligned, and flat. Clamp and allow wood glue to dry completely. Notice that the 2x8 boards are the outer boards and the 2x10 boards are on the inside.

4

Attach the Breadboards

Measure the width of the constructed tabletop and cut the breadboards to fit. It's best to use mortise and tenon joinery to attach the breadboard ends to the tabletop. The floating tenons will allow for wood movement as the wood expands and contracts due to changes in temperature and humidity.

5

Install Figure 8 Tabletop Fasteners

Use a forstner bit to drill an inset hole for the figure 8 tabletop fasteners to sit flush into the aprons. This will be to attach the tabletop in the next step. These tabletop fasteners will allow for wood movement as the wood expands/contracts due to temperature and humidity changes.

6

Attach the Base to The Tabletop

Center the base over the tabletop as shown and secure the base to the top with figure 8 tabletop fasteners. There should be a 3 1/2" overhang on all sides. Sand, paint and/or stain, and finish as desired.

7

Visit JenWoodhouse.com

For more free building plans and DIY project ideas, visit www.JenWoodhouse.com

Tools Used:

Materials Required:

Wood Products:

(3) 2x4, 96", Board  
(3) 2x10, 96", Board  
(4) 2x8, 96", Board  
(4) 3 1/2" x 3 1/2", 29", Turned Dining Table Legs  

Hardware/Supplies:

Parts/Cut List:

(4) Turned Dining Table Legs, 29"  
(2) 2x4 Long Aprons, 1 1/2" x 3 1/2" x 66"  
(2) 2x4 Short Aprons, 1 1/2" x 3 1/2" x 27"  
(3) 2x4 Supports, 1 1/2" x 3 1/2" x 29 1/2"  
(3) 2x10 Tabletop Boards, 1 1/2" x 9" x 66"  
(2) 2x8 Tabletop Boards, 1 1/2" x 7" x 66"  
(2) 2x8 Breadboards, 1 1/2" x 7" x 41"  

Extras:

http://www.jenwoodhouse.com Visit

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!