Antique Style Hutch

 Write Review

sincerely, marie designs added on 10/26/2016

Antique, shaker style hutch & cabinet. Great for displaying all your dishes and dining utensils as well as plenty of storage below with an extra shelf.

Directions

Follow the steps below to complete this project.

1

Building Cabinet Base

Make all pocket holes in the cabinet sides, cabinet support and bottom shelf. Attach cabinet sides to cabinet bottom support using 1 1/4" Kreg screws. Attach bottom shelf using 1 1/4" Kreg screws as well.

2

Adding Cabinet Face Frame

Attach top, bottom and side face frame using 1 1/4" Kreg screws and wood glue.

3

Adding Cabinet Shelf & Top

Using glue and brad nails attach the shelf supports making sure they're flush with the backs of the cabinet sides. Add the cabinet top using 1 1/4" Kreg screws.

4

Adding Cabinet Trim

Cut to size and nail in desired trim around the base of the cabinet as well as around the cabinet top if you choose.

5

Make Cabinet Doors

Attach cabinet sides using wood glue and 1 1/4" Kreg Screws. Using a staple gun and wood glue, attach plywood backing to the backside of the doors.

6

Assemble Hutch Frame

Attach hutch sides to bottom support with 3/4" pocket holes using 1 1/4" Kreg screws. Add hutch top by pocket holes and Kreg screws or use wood screws and drill in from the side. This will be covered later with crown molding. Add hutch side face frames using wood glue and brad nails. Attach top face frame using 1 1/4" Kreg screws.

7

Add Hutch Shelves

Add middle face frame using 1 1/4" kreg screws. Find the center point and attach at top of the face frame and attach at the bottom by screwing into the top of the cabinet once in place. Add your shelf supports with wood glue and brad nails. Make sure the supports are flush with the back of the cabinet.

8

Attach Hutch to Cabinet

Attach the hutch to the cabinet by screwing middle hutch face frame onto the cabinet top and by adding mending plates to the back of the hutch sides and cabinet sides. There should be about 3/4" cabinet over hang on each side of the hutch.

9

Attaching The Cabinet Doors

Hang doors with desired hinges, leaving an 1/8" gap around. Attach desired knobs or latches. The hardware shown here was all purchased at Home Depot.

10

Add Backer Board

Add 1/4" plywood cut to size to the back of the hutch and cabinet using a staple gun.

11

Finishing

Fill all holes and cracks with wood filler and sand with 120 grit sand paper and stain or paint with color of choice. Seal with a clear top coat and sand lightly with 400 grit sand paper for a super smooth finish.

12

Visit The Tale of an Ugly House

Visit me at TheTaleofanUglyHouse.com

Tools Used:

Materials Required:

Wood Products:

(1) 3/4" Thick, Full Sheet, Plywood  
(4) 1x3, 96", Board  
(1) 1x3, 48", Board  
(1) 1x4, 96", Board  
(1) 1/4" Thick, Full Sheet, Plywood  
(1) 1/4" Thick, Half Sheet, Plywood  
(2) 1x12, 96", Board  
(1) 3/4" Thick, 96", Decorative trim of choice  
(1) Crown Molding of Choice, 96", Board  

Hardware/Supplies:

(2) Cabinet door hinges of choice  
(2) Door latches of choice  
(1) Wood glue  
(1) Wood Filler  
(1) Box 1" Kreg screws  
(1) Box 1 1/4" Kreg screws  
(1) Box 1 1/2" Kreg Screws  
(1) Box Brad nails  
(1) Pack 120 grit sand paper  
(1) Pack 400 grit sand paper  
(1) Paint or stain or choice  
(2) Mending Plates to attach hutch to cabinet  

Parts/Cut List:

(2) Hutch Sides, 3/4" x 12" x 46 1/4"  
(1) Hutch Top, 1" x 12" x 4'  
(2) Hutch Side Face Frames, 1" x 3" x 46 1/4"  
(1) Hutch Top Face Frame, 1" x 4" x 44.5"  
(3) Hutch Crown Molding, Cut to size  
(3) Bottom Cabinet Trim, Cut to size  
(1) Cabinet Shelf (optional), 1" x 12" x 4'  
(6) Shelf supports, 1" x 2" x 11 1/4"  
(4) Cabinet Door Frame, 1" x 3" x 23"  
(4) Cabinet Door Frame, 1" x 3" x 15 3/4"  
(2) Cabinet Door Center Panel, 1/4" x 20" x 18"  
(2) Hutch Shelves, 1" x 12" x 4'  
(1) Top Hutch Board , 1" x 12" x 4'  
(1) Bottom Hutch Support, 1" x 4" x 4'  
(2) Cabinet Sides, 3/4" x 17" x 33"  
(1) Cabinet Bottom, 3/4" x 17" x 4'  
(1) Cabinet Bottom Support Board , 2" x 3" x 4'  
(1) Cabinet Top, 3/4" x 18 3/8" x 51 1/2"  
(1) Bottom Cabinet Face Frame, 1" x 4" x 44 1/2"  
(2) Side Cabinet Face Frames, 1" x 3" x 29"  
(1) Cabinet Top Face Frame , 1" x 3" x 44 1/2"  
(1) Cabinet Middle Face Frame, 1" x 3" x 23 1/4"  
(3) Cabinet Top Trim Edging, Cut to size  

Extras:

No extra details have been uploaded.  

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!

    Kreg Tool