Wall Mounted Spice Rack

 Write Review

housefulofhandmade added on 1/4/2018

Free up counter space and cabinet space by displaying your spice collection on the wall of your kitchen. This quick project will help you organize your kitchen, and acts as beautiful wall decor too.

Directions

Follow the steps below to complete this project.

1

Build back of spice rack

Cut 1x8 into 3 30" pieces. Join the boards along the edges by drilling pocket holes in the sides of the center board about 5-6" apart. Make sure the pocket hole on the top of the boards is low enough that it will not be cut through when you add the decorative top. Apply wood glue to the edges of the boards, clap them together and secure with 1 1/4" pocket hole screws.

2

Cut decorative top

Sketch out the decorative top you want on your spice rack or download the one I used in the extras tab. Cut out the template and trace it on one half of the top of your connected boards. Then flip and trace the other side. Cut along the lines with a jig saw.

3

Add optional router edge

To add a farmhouse look to my spice rack, I used my router to apply a decorative edge to the front edges of the spice rack back.

4

Cut boards for the spice shelves

My spice shelves were built to hold spice jars that are 2 1/16" x 2 1/16". Measure your spice jars and adjust as necessary. Cut the 1x3 board into (3) 25" pieces and then rip those pieces into 2 1/4" wide boards. Do not discard the ~1/4" wide piece that is remaining. If you do not have a table saw, you can easily rip boards with the Kreg AccuCut and a circular saw by using a second piece of wood to balance the AccuCut. Or feel free to leave the boards 2 1/2" wide and purchase 1/4" x 1/2" trim for the front of the shelves. Cut each of the 2 1/4" wide boards into (1) 18 1/2" piece and (2) 2 3/4" pieces.

5

Build the spice shelves

Drill pocket holes into both ends the top of the 18 1/2" pieces. Line the 2 3/4" pieces up on the edges to create a U and secure with wood glue and pocket hole screws. Cut the ~1/4" piece to 20" and attach to the top front of the spice shelves with wood glue and finishing nails.

6

Sand and finish back & shelves

If you want to add a chalkboard back like I did. Sand, stain or paint, and seal all the spice shelves and the back piece before attaching the shelves. For the chalkboard back, apply 3 coats of chalkboard paint. Then prime the chalkboard by rubbing the side of a piece of chalk over the entire surface then wiping it off with a cloth or eraser before attaching the spice shelves.

7

Attach the spice shelves

Measure and mark where you want to attach your spice shelves. Make sure you have enough room between shelves to easily remove your spice jars. My jars are 4 1/2" tall so I spaced my shelves 4 3/4" apart. Drill holes through the back of the spice rack where you will attach the shelves. Then attach the shelves with wood glue and 1 1/4" wood screws from the back of the spice rack.

Tools Used:

Materials Required:

Wood Products:

(1) 1x8, 96", Board  
(1) 1x3, 96", Board  

Hardware/Supplies:

Parts/Cut List:

(3) Back boards, 3/4" x 7 1/4" x 30"  
(3) Spice shelf bottoms, 3/4" x 2 1/4" x 18 1/2"  
(6) Spice shelf sides, 3/4" x 2 1/4" x 2 3/4"  
(3) Spice shelf front, 1/4" x 3/4" x 20"  

Extras:

curved-top-template.pdf Download
http://housefulofhandmade.com/wooden-spice-rack-build-plans/ Visit

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!

    Kreg Tool