Outdoor Ping-Pong Table

 Write Review

buildsomething added on 8/9/2018

Take your backyard fun to a new level with this cool outdoor ping-pong table. With a cedar base and a top made from cement board (usually used for tile underlayment), this table will hold up for years of fun outside. You can build one for yourself with a few tools and a Heavy-Duty Kreg Jig.

Directions

Follow the steps below to complete this project.

1

Cut the Corner Legs

Start by cutting the four Corner Legs to length from 4x4 boards, as shown in the cutting diagram. Then sand the Legs smooth.

 How To Crosscut Boards on a Miter Saw

Learn how to crosscut boards on a miter saw accurately and safely so that you get great results every time. 

2

Make the Rails

From 2x6 boards, cut two End Rails, two Long Rails and one Center Rail to length. Now you can drill pocket holes. For this project, we chose the Kreg Jig® HD. It drills a larger pocket hole to accept a bigger screw that’s made for building with 2x4 and larger boards. Using the Kreg HD Jig and drill bit, drill pocket holes on each board at the locations shown. Sand the Rails smooth after you drill the pocket holes.

 How To Make Square Cuts with a Circular Saw

Learn how to cut boards to length accurately using a circular saw, and get straight, square cuts. 

3

Assemble the Ends

Now you can start assembly with two Legs and one Short Rail. Apply exterior glue to the pocket-hole ends of the End Rails. And then position the End Rail so it is centered on the width of each Leg and flush at the top, as shown. Secure the Short Rail with Kreg HD Screws as shown. Repeat the process to assemble the other end section.

4

Attach the Remaining Rails

Apply glue to the pocket-hole ends of one Long Rail, and then position it between tow end assemblies, as shown. Make sure the Long Rail is centered on the width of each Leg and flush at the top edge. Secure the Long Rail using Kreg HD Screws. Do the same for the second Long Rail. Next, position the Center Rail so it is centered on the Short Rail and flush at the top as well. Secure it with Kreg HD Screws. Finally, Add the other end assembly so the base will stand on its own.

5

Make the Center Legs

From a 4x4 board, cut two Center Legs to length, as shown in the cut diagram. Now lay out the notch on each Leg. Set your circular saw blade to the 2" depth of the notch, and then make a cut across the Leg at the 5 1/2" mark. Make consecutive cuts close to one another, working your way toward the upper end of the Leg, as shown in the Tip below.

 TIP: USE MULTIPLE CUTS TO MAKE A NOTCH

When you need to cut a wide notch, you don’t need a wide saw. You can do it by making multiple cuts. First make a cut to establish the end of the notch, then make more cuts close together. You’ll end up with a surface that looks like a comb when viewed from the side. Next, use a hammer to strike against the side of the cut material to dislodge it from the Leg. When the pieces are removed, you’ll be left with a rough surface. Use a chisel or a sharp utility knife to cut away any large remaining pieces, and then smooth out the surface of the notch using a sander and 80-grit sandpaper. Then sand the rest of each Center Leg smooth.

6

Install the Center Legs

Position the Center Legs so they are centered on the length of the Long Rails. Apply exterior wood glue on the Leg notch and clamp it into position. Make sure the Leg is perpendicular to the Rail. Secure the Leg to the Rail with two Kreg HD screws, as shown. Though you’re not using pocket holes here, the HD Screws work great. The self-tapping tips make it easy to drive in the screws without splitting the wood. Note the locations of the screws. They should be offset to the left side of the Leg as you face it. That way, they won’t interfere with mounting the Center Supports in the next step. Repeat this process to attach the other Center Leg.

7

Make the Center Supports

Cut two Center Supports to length from a 2x6 board as shown in the cutting diagram. Using the Kreg Jig HD, drill pocket holes at the locations shown. Sand the Supports.

8

Install the Supports

Apply glue to the ends of the first Center Support, and then position it so it’s offset to the right side of the Center Leg, as shown. Secure it with Kreg HDS. Then attach the second Center Support in the same way.

9

Make the Braces

From 2x6 material, cut six Corner Braces to length by beveling each end at 45°, as shown in the cut diagram. In four of the braces, drill six pilot holes at the locations show. In the other two Braces, drill four pilot holes.

 How To Cut Angles on a Miter Saw

Learn how to make two kinds of angled cuts on a miter saw: A miter cut and a bevel cut. A miter saw makes them easy, and allows you to expand your project-building capabilities.

10

Install the Braces

Apply exterior wood glue to the beveled ends of each Brace, and then position them where shown. The braces with six holes go at the outside corners, while the braces with four holes sit against the Center Supports and Long Rail. secure them where shown using Kreg HD Screws.

11

Set the Top in Place

Set the cement-board Top Panels on the frame and adjust them so they overhang the base equally. Make sur ethe smooth face of each panel is facing up. Handle the panels gently until you have the edging installed (in the next steps) because flexing the cement board too much can cause it to snap.

12

Cut the Edging to Length

To strengthen the top panels, you’ll want to add edging. It’s made from 1x4 boards, and gets attached to the underside of the Top Panels using construction adhesive. Start by cutting two End Edges, four Side Edges, and two Center Edges to length from 1x4 boards, as shown in the cutting diagram. Don’t cut the notches yet. You’ll do that in the next step.

13

Install the Edging

Start edging installation at the ends. Apply a bead of construction adhesive to one face of each piece of End Edging. Then clamp it in position, as shown, so it sits flush with the end of the table top, and the ends align with the top edges. Next, place the First Side Edging in general position so it’s butted against the End Edging. Mark the location where you need to notch for the Corner Leg. Remove the Edging, cut the notch out with a jigsaw, and then reposition it to check the fit. If it fits properly, apply construction adhesive and clamp it in its final position. Do the same with each piece of Corner Edging—test fitting, cutting, and attaching each one. Finally, notch and attach the Center Edging.

 How To Cut a Square Notch with a Jigsaw

Learn how to use use a jigsaw to cut out a notch quickly and easily with this simple technique

14

Apply Paint and Finish

After the construction adhesive has had time to cure, you can paint the table top and apply finish to the base. Before you remove the remove the Top Panels, use a permanent marker to trace the position of the base rails on the underside of the table top panels. That way you’ll be able to easily reposition them on the base. Clean dust off he panels and wipe them down with a damp rag. Then paint both face of each panel to seal them. We used a porch and patio paint tinted to a dark grey. After the paint dries, mask off the edge and a line down the center and paint the lines white or a lighter contrasting color. Finally, apply an exterior oil finish to the base.

Tools Used:

Materials Required:

Wood Products:

(5) 2x6, 96", Board  
(2) 4x4, 96", Board  
(3) 1x4, 96", Board  

Hardware/Supplies:

Parts/Cut List:

(4) Corner Leg, 3 1/2" x 3 1/2" x 30" cedar  
(2) Short Rail, 1 1/2" x 5 1/2" x 47 3/4" cedar  
(2) Long Rail, 1 1/2" x 5 1/2" x 94" cedar  
(1) Center Rail, 1 1/2" x 5 1/2" x 96" cedar  
(2) Center Leg, 3 1/2" x 3 1/2" x 30" cedar  
(2) Center Support, 1 1/2" x 5 1/2" x 24 1/8" cedar  
(6) Corner Brace, 1 1/2" x 5 1/2" x 6" cedar  
(3) Top Panel, 1/2" x 36" x 60" cement backer board  
(2) Top End Edging, 3/4" x 3 1/2" x 60" cedar  
(4) Top Side Edging, 3/4" x 3 1/2" x 33 1/2" cedar  
(2) Top Center Edging, 3/4" x 3 1/2" x 34" cedar  

Extras:

No extra details have been uploaded.  

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!

    Kreg Tool