Modern Coffee Table

 Write Review

housefulofhandmade added on 3/15/2020

Build this beautiful modern coffee table with just a few pieces of lumber. The simple angled legs give your room a clean, open feel. And bonus, the open legs make it easier to vacuum under the coffee table without having to move it.

Directions

Follow the steps below to complete this project.

1

Rip leg sides

Set your table saw to cut at a 15 degree angle. Rip the edge off one edge of all 4 leg side boards.

2

Cut leg boards

Cut each end off all 4 of the leg boards at a 15 degree angle. The angled ends should be parallel.

3

Cut taper on leg boards

Lay one of the 1x2 leg side pieces on the bottom of the angled leg piece so the bottom and front are flush. Mark the top corner. Draw a straight line from the top inside corner of the leg to the bottom, going through the corner mark. Cut the legs off along this line to create a taper.

4

Rip bottom leg sides

Transfer the angle to the non-ripped side of 2 of the leg side boards (these will be the bottoms of the legs). Check the angle, it will be approximately 22.5 degrees. Set the table saw to the new angle and rip off the other side of the 2 leg side boards.

5

Assemble legs

Set your pocket hole jig for 3/4" thick material. Drill 1 pocket hole in the bottom of each of the bottom leg side pieces. Also, drill 2 pocket holes in the back of the other 2 leg side boards. Double check your angles to make sure the boards line up correct when assembled and the two legs are mirrored. Attach the leg side boards to the leg boards with 1 1/4" pocket hole screws and wood glue.

6

Attach leg apron

Cut the ends of the leg apron boards so they are the same angle as the second cut on the bottom leg sides (approximately 22.5 degrees). The angled cuts will be opposite so they angle towards each other. Drill 1 pocket hole in each end of the apron board. Be careful that the entire pocket hole is hidden inside the 1x2 apron board. Attach the apron between the two legs with a 1 1/4" pocket hole screw and wood glue.

7

Build table top

Set your pocket hole jig for 1 1/2" thick material. Drill pocket holes along the side of 3 of the top slat boards. Drill pocket holes so they are 5-6 inches apart. Assemble the table top by applying hot glue to the edges of the boards, clamps them tight, and secure with 2 1/2" pocket hole screws.

8

Finish the coffee table

Sand stain/paint and seal your coffee table legs and top. To attach the table top, secure the L clips to the top inside of the legs. Then lay the legs, upside down, on top of the table top. Center the legs and attach the other end of the L brackets to the top.

9

Enjoy!

Flip your table over and enjoy the great modern, open look. For more details on how I finished my coffee table and more fun things to build, make sure to come say hi at Housefulofhandmade.com.

Tools Used:

Materials Required:

Wood Products:

(1) 1x4, 72", Board  
(2) 1x2, 72", Board  
(2) 2x6, 96", Board  

Hardware/Supplies:

(16) 1 1/4" pocket hole screws  
(15) 2 1/2" pocket hole screws  
(1) Wood glue  
(6) 1 1/2" L brackets with screws  

Parts/Cut List:

(4) Legs, 3/4" x 3 1/2" x 18"  
(4) Leg sides, 3/4" x 1 1/2" x 16"  
(2) Leg apron, 3/4" x 1 1/2" x 30"  
(4) Top slats, 1 1/2" x 5 1/2" x 48"  

Extras:

https://housefulofhandmade.com/ Visit

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!

    Kreg Tool