Entryway Bench with Shoe Rack

 Read Reviews (2)

buildsomething added on 3/8/2019

Upgrade your entryway with style and storage with this great-looking bench that you can build for less than $30 in lumber. The bench is made from two 2x8s, a 1x12, and a square dowel. Pocket-hole construction makes it simple to put together, and the design is perfect for a rustic, farmhouse look.


Follow the steps below to complete this project.


Make the Seat Boards

Cut two Seat boards to length from 2x8 lumber, as shown in the cutting diagram. If you have a miter saw, you can use irt to cut all the pieces. If you don’t have one, see the how-to-tip below for an easy way to make straight, square cuts with a circular saw. Set your Kreg Pocket-Hole Jig for 1 1/2"-thick material, and then drill pocket holes along the edge of just one of the Seat boards, as shown.

 How To Make Square Cuts with a Circular Saw

Learn how to cut boards to length accurately using a circular saw, and get straight, square cuts. 


Assemble the Seat

Assemble the two Seat boards by applying glue along the edge of the one with pocket holes, and then clamping the boards together so the ends are flush. Drive in 2 1/2" coarse-thread Kreg Pocket-Hole Screws to draw the boards together.

 How To Choose the Correct Kreg Screw

Learn how to choose the correct Kreg Screw for your project based on the material you are using and where you'll place the project—indoors or outdoors.


Make the Leg Boards

Cut four Legs from a 2x8 board, as shown in the cutting diagram. Drill pocket holes in each of the Leg boards as shown. Note that the boards with the pocket holes along the edge as well as the end should mirror each other. This is so the holes face inward and are oriented in the same direction when you assemble the base.

 How To Set Up a Kreg Jig in Three Simple Steps

Learn how easy it is to set up a Kreg Jig® and ensure that you'll drill pocket holes accurately every time.


Assemble the Legs

Glue and clamp two Leg Boards together as shown, making sure that the pocket holes are all oriented correctly, as shown. Secure the Leg boards using 2 1/2" coarse-thread Kreg Pocket-Hole Screws. Repeat this process for the other Leg. Note the other Leg assembly should mirror the first.

 How To Choose and Use Wood Glue

Learn how to choose the right wood glue for your project, and get tips for applying it correctly.


Make the Back Rail

With the leftover section of 2x8 board, cut the Back Rail to final length. Drill pocket holes on each end and along one edge as shown.


Assemble the Base

Spread glue on the ends of the Back Rail. Then position the Back Rail between the Legs, as shown, so it is flush at the rear edge and along the upper end, and with the pocket holes facing toward the back of the bench. Make sur ethe pocket holes along the edge of the Back Rail face upward for attaching the Seat later. Clamp the Back Rail and Legs, and then secure them using 2 1/2" coarse-thread Kreg Pocket-Hole Screws.


Attach the Seat

Set the Seat flat on a work surface with the pocket holes facing up. Place the base and center it on the Seat. The Base should be flush with the Seat at the front and back. Secure the two assemblies using glue and 2 1/2" coarse-thread Kreg Pocket-Hole Screws.


Make the Shelf

Cut the Shelf to length from a 1x12 board, as shown in the cutting diagram. Change the settings on your Kreg Pocket-Hole Jig and drill bit for 3/4"-thick material. Then drill pocket holes in each end of the Shlef, and along one edge, as shown.


Add the Cleat

Cut the Shoe Cleat to length from a 1"x1" square dowel, as shown in the cutting diagram. Spread glue along the pocket-hole edge of the shelf, and then clamp the Cleat to it. The Cleat should be flush at the bottom of the Shelf. Now attach the Cleat to the Shelf with 1 1/4" coarse-thread Kreg Pocket-Hole Screws.


Install the Shelf

Position the shelf in the general location shown. You can adjust the angle and position here to suit your own needs. Secure the Shelf to the Legs using 1 1/4" coarse-thread Kreg Pocket-Hole Screws. You can assemble without glue here. That way, if you decide later that you need to reposition the Shelf, it will be easy


Apply the Finish

Now you can sand and finish the bench. Because we were going for a rustic look, we only sanded lightly to ease any sharp edges, and to get rid of major scratches. Then wipe away sanding dust and apply the finish of your choice. We used a Java gel stain. After the stain dries, apply a durable top-coat, like a wipe on polyurethane.

 How To Apply Gel Stain

Learn how to get great results when you're staining wood projects by using gel stain. It makes staining easier than you might have imagined.

Tools Used:

Materials Required:

Wood Products:

(2) 2x8, 96", Board  
(1) 1x12, 48", Board  
(1) 1" x 1", 36", Square Dowel  


(1) wood glue Shop Online
(28) 2 1/2" coarse-thread Kreg Pocket-Hole Screws Shop Online
(11) 1 1/4" coarse-thread Kreg Pocket-Hole Screws Shop Online

Parts/Cut List:

(2) Seat, 1 1/2" x 7 1/4" x 45"  
(4) Leg, 1 1/2" x 7 1/4" x 15 1/2"  
(1) Back Rail, 1 1/2" x 7 1/4" x 32"  
(1) Shelf, 3/4" x 11 1/4" x 32"  
(1) Shelf Cleat, 1" x 1" x 32"  


No extra details have been uploaded.  


You must log in to add comments


    Become a Member


    • Connect with the BuildSomething Community
    • See what others build and share your stories


    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed


    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com



    Already a member?
    Sign in!

    Kreg Tool