Easy-To-Build Nightstand

 Read Reviews (1)

buildsomething added on 6/15/2015

Create storage space next to your bed and add style to your bedroom with this nightstand. It’s easy to build, even with the distinctive legs that sit at 45° angles. You can go for a traditional look like this using oak, choose maple for a modern style, or build one from pine and paint it.

Directions

Follow the steps below to complete this project.

1

Create the Legs

Cut four Legs to length from a 1x4 board, as shown in the cutting diagram.

2

Cut the Rails

Now you can cut four Rails from a 1x4 board, as shown in the cutting diagram. To do that, you’ll need to set your miter saw to a 45° bevel angle. If your saw doesn’t have bevel-cutting capability, you can instead stand the board on ages and rotate the blade for 45° miter cuts instead. Then, with your pocket-hole jig set up for 3/4" material, drill pocket holes in the back face of the Top Rail, as shown.

3

Drill Pocket Holes in the Rails

With the Rails cut, it’s time to drill pocket holes. Because of the mitered ends, this takes a couple of setups. Start with your pocket-hole jig and the drill bit set up for 3/4" material, and drill the pocket holes along the edge of each rail, as shown. For the ends, keep your jig at the 3/4" setting, but change the drill bit to the 1/2" setting. Then drill pocket holes as shown.

4

Attach the Rails to the Legs

After sanding the Rails and Legs, you can connect them. To do that, join two Rails to one Leg, as shown, using 1 1/4" fine-thread pocket-hole screws. Then make another assembly just like it.

5

Add the Other Legs

Now you can connect the other two Legs using 1 1/4" fine-thread pocket-hole screws.

6

Create a Shelf

Cut a Shelf to size from 3/4" plywood, as shown in the cutting diagram. Then clip off the corners, as shown. Once you’ve done that, drill a pair of pocket holes at each corner with your pocket-hole jig set up for 3/4" material. Cover edges of the plywood that will be exposed with iron-on edge banding. (Or, if you intend to paint, fill the edges with spackling compound, and then sand it smooth.)

7

Install the Shelf

With the Shelf done, you can attach it to the Legs using 1 1/4" fine-thread pocket-hole screws.

8

Make the Top Slats

Cut four Top Slats to length from a 1x6 board, as shown in the cutting diagram. Then, with your pocket-hole jig set up for 3/4" material, drill pocket holes in the Top Slats as shown.

9

Assemble the Top

After sanding the top slats, connect them using 1 1/4" fine-thread pocket-hole screws.

10

Mount the Top and Finish

To complete your nightstand, mount the Top to the base. Lay the Top face down and position the base on the Slats so that there are equal overhangs on all sides. Then attach the Top to the Rails using 1 1/4" fine-thread pocket-hole screws. Then coat the nightstand with the finish, stain, or paint of your choice.

Tools Used:

Materials Required:

Wood Products:

(1) 1x4, 96", Board  
(1) 1x4, 72", Board  
(1) 1x6, 96", Board  
(1) 3/4" Thick, Quarter Sheet, Plywood  

Hardware/Supplies:

Parts/Cut List:

(4) Legs, 3/4" x 3 1/2" x 19 1/4"  
(4) Rails, 3/4" x 3 1/2" x 16 1/4"  
(4) Top Slats, 3/4" x 5 1/2" x 22"  
(1) Shelf, 3/4" plywood x 19" x 19"  

Extras:

No extra details have been uploaded.  

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!

    Kreg Tool