Waterfall Edge Modern Nightstand

 Read Reviews (1)

pneumatic addict added on 10/23/2019

Whether you're using an exotic live edge board or inexpensive plywood, this simple one drawer nightstand shows off the beautiful natural grain of the material. The clean mitered corners add to the sleek and modern lines of the piece. Build a pair with just two sheets of 3/4" plywood!

Directions

Follow the steps below to complete this project.

1

Laminate Panels

Laminate 14" x 96" plywood pieces and 14" x 17" plywood pieces together to create 1-1/2" thick panels. Apply wood glue to adjoining faces and clamp together while they dry.

2

Miter Panels

Cut 1-1/2" thick laminated panels into sequential left side, top, and right side pieces. Use the KregĀ® Adaptive Cutting System, circular saw or table saw to cross-cut opposing, 45 degree miters. Cut the ends of the leg panels square at 90 degrees.

3

Attach Sides to Top

Attach mitered, 1-1/2" thick sides to top. Apply glue and clamp mitered edges together. Clamp in place and allow to dry. Once dry, secure pieces together using 1-1/4" screws driven through pocket holes.

4

Attach Shelf

Space lower shelf between sides, 3-1/2" from the bottom edge. Secure in place using wood glue and 2-1/2" screws through pocket holes.

5

Back Board

Insert back board along the top edge of the opening. Secure in place using glue & 1-1/4" screws through pocket holes.

6

Build Drawer Boxes

Measure the exact width of the opening between sides of the nightstand. Use those dimensions to build a 3-1/2" tall, 12" deep drawer box using your preferred technique.

7

Install Drawers

Place drawer box inside opening, spaced approximately 1-3/4" from the top inside edge. Install using 1/2" drawer slides.

8

Add Drawer Face

Place drawer face in front of drawer box. Allow a 1/8" gap around all sides of the opening. Clamp in place temporarily. Pre-drill from the inside of the drawer box and secure using 1-1/4" screws.

9

Attach Drawer Handle

Center scrap plywood drawer handle on drawer face. Clamp in place temporarily. Pre-drill from the inside of the drawer box and secure with 2" screws.

10

Watch Build Video

Head to http://www.pneumaticaddict.com or https://youtube.com/pneumaticaddict to watch the build video and pick up some tips and tricks I learned as I completed this project.

Tools Used:

Materials Required:

Wood Products:

(1) 3/4" Thick, Full Sheet, Plywood  
(1) 1/4" Thick, Quarter Sheet, Plywood  

Hardware/Supplies:

(50) 2-1/2" pocket hole screws  
(50) 1-1/4" pocket hole screws  
(100) 1-1/4" 23-gauge pins  
(1) 12" drawer glides  

Parts/Cut List:

(2) Body Panels, 3/4" x 14" x 96"  
(2) Shelf Panels, 3/4" x 14" x 17"  
(1) Back Board, 3/4" x 17" x 5-5/8"  
(1) Drawer Face, 3/4" x 16-3/4" x 5-5/8"  
(2) Drawer Box Side, 3/4" x 3-1/2" x 10-1/2"  
(2) Drawer Box Front/Back, 3/4" x 3-1/2" x 16" approx.  
(1) Drawer Box Bottom, 1/4" x 11-1/4" x 15-1/4" approx.  
(1) Scrap Handle, 3/4" x 1" x 5-5/8"  

Extras:

https://www.youtube.com/pneumaticaddict Visit
https://www.pneumaticaddict.com/ Visit

Discussion

You must log in to add comments

Login

    Become a Member

    Explore

    • Connect with the BuildSomething Community
    • See what others build and share your stories

    Contribute

    • Find inspiring ideas for your projects you can build
    • Get the step-by-step plans you need to succeed

    Share

    • Turn your projects into professional-looking plans
    • Share your plans you create on buildsomething.com

    OR

    CONNECT USING

    Already a member?
    Sign in!

    Kreg Tool